Ducati Diavel
Free Service and Repair manuals

Ducati Diavel Service Manual: Gear indicator display on dashboard shows dashes, engaged gear not displayed correctly, idle speed irregular with gearbox in neutral

Ducati Diavel Service Manual / Electric system and engine control system / Bbs and db faults / Gear indicator display on dashboard shows dashes, engaged gear not displayed correctly, idle speed irregular with gearbox in neutral

Fault codes

Dds: gear sensor diagnosis -> short circuit to ground or open circuit (s.C. Gnd or c.O.) - Short circuit to vdc (s.C. Vdc) - congruence (generic error - signal not correct).

Dashboard: the error "gear sensor" is shown on the service display. The eobd warning light activates.

Fault indication

If the dashboard receives the "gear" error information via the can line:

If the dashboard does not receive the gear or neutral engaged information via the can line:

If the dashboard receives incorrect gear engaged information (flashing dashes) via the can line with the engine running:

Warning

It is possible that the gear engaged or neutral engaged information is not being generated because the gear position self-acquisition procedure has not been performed (gear sensor not initialised).


Wiring diagram

Wiring diagram


Bbs bbs unit connection, s gear position sensor. Bbs 15 brown/red - br/r (5v), bbs 13 yellow/green y/g, bbs 10 black/blue - bk/b.

Location of connections and components

Location of connections and components


Location of gear sensor connection

Location of connections and components


Pin numbering of wiring harness side bbs unit connection.

Checks

The gear sensor is a hall effect unit. Ground is on pin 10 of the bbs unit, 5 v power is on pin 15 of the bbs unit, pin 13 of the bbs is the input for the signal generated by the sensor. Check that the sensor receives 5 v power.

Check the integrity of the electrical circuit and connections (short-circuits to ground, short-circuits to vdc, open circuits).

Perform the gear self-acquisition procedure.

If none of the aforementioned tests identify the problem, replace the gear sensor then perform the gear self-acquisition procedure. If the fault has not been resolved, replace the bbs unit.

Warning

The engine control unit uses the neutral engaged signal generated by the gear sensor, together with the clutch lever pulled signal, to manage idle speed.

Note

Check integrity of electric circuit - short-circuit to vdc = with dashboard on, using a voltmeter, a voltage is measured between the wire tested and ground.

Check integrity of electric circuit - short-circuit to ground = with the battery cables disconnected, using an ohmmeter, continuity is detected between the wire tested and ground.

Check integrity of electric circuit - open circuit = with the battery cables disconnected, using an ohmmeter, no continuity is detected between the two ends of the wire tested.

Gear self-acquisition procedure

The gear self-acquisition procedure must be launched from the dds instrument. This ensures that the data stored previously is deleted and enables the bbs to run a new gear acquisition procedure. With the engine running and the motorcycle in motion:

Gear self-acquisition procedure


Resetting turn indicators not possible - accessing dashboard menu not possible
Fault codes Dds: no fault code displayed Dashboard: no fault code displayed Location of connections and components Location of left hand handlebar switchgear set connection. Pin numbering ...

Dashes shown instead of speed indication or indicated speed is incorrect
Fault codes Dds: speed sensor diagnosis -> max. Speed (max. Speed error - signal not correct) - minimum speed (min speed error - signal not correct) - congruence (correlation speed error - sign ...

Other materials:

Removal of the front footrests
Note The removal of the front footrests is described only for the right one (2) but it is the same also for the left one. Remove the circlip (5) by releasing the pin (3). Slide the pin (3) off the frame by supporting the footrest (2). Slide off the footrest (2) from its seat and collect th ...

Introduction to the engine control system
The engine control system used on the diavel consists of the following elements: Ride-by-wire system (motorised throttle valves with electric actuator, throttle grip position sensor and throttle valve position sensor) One injector per cylinder installed downstream of throttle valve On ...

Reassembling the front footrest brackets
To reassemble the brackets (6) and (21) carry out the removal procedure in the reverse order; tighten the screws (7) to a torque of 25 nm +/- 10% (sect. 3 - 3, Frame torque settings). ...

2025 | www.dudiavel.com |