Ducati Diavel
Free Service and Repair manuals

Ducati Diavel Service Manual: Reassembly of the cylinder head

The exhaust side can be identified by the three threaded holes on the flange.

Reassembly of the cylinder head


The intake side can be identified by the presence of four threaded holes on the flange.

Reassembly of the cylinder head


All the photos in this chapter refer to a vertical cylinder head.

Valve guide sealing rings

Position the cylinder head on the appropriate support 88713.2103.

Lubricate the valve guides seal rings (8) with engine oil and insert them from the spring side onto tool 88713.2442.

Fit the end of the tool into the valve guide and use a mallet to tap the sealing rings (8) home into the valve guides.

Valve guide sealing rings


Reassembly of the closing rocker arms

Check that the rocker arms are not scored or show signs of breakage in the area of contact with the camshaft and shim.

The closing rocker arm shafts are 10 mm in diameter, whereas the opening rocker arm shafts are 9 mm in diameter.

Using an m6 screw, position the closing rocker shaft (1) towards the exhaust side of the cylinder head.

Reassembly of the closing rocker arms


Reassembly of the closing rocker arms


Locate the spacer (17) on the shaft.

Reassembly of the closing rocker arms


Locate the spring (18) on the spacer (17) as shown, fitting one end of the spring in its seat in the cylinder head.

Reassembly of the closing rocker arms


Reassembly of the closing rocker arms


Locate the closing rocker arm (16) into its seat, making sure that the through hole is in line with the closing rocker arm shaft and drive the shaft home.

Reassembly of the closing rocker arms


Proceed in a similar manner to install the closing rocker arm (4) with the spring (19).

Reassembly of the closing rocker arms


Load the springs (18) and (19) on the closing rocker arms (16) and (4) respectively using the tool 88713.2069.

Reassembly of the closing rocker arms


Reassembly of the closing rocker arms


Proceed to install the closing rocker arms (4) and (16), the springs (24) and (25), the relative pins on the exhaust side in the same manner as described for the intake side.

Note

Always install the closing rocker arms on the exhaust side before those on the intake side.

Warning

Take care not to damage the shoe of the closing rocker arm with the intake spring during assembly.

Reassembly of the closing rocker arms


Refitting the valves, closing shims and half rings

Carefully clean the two intake valve seats (a) and the two exhaust valve seats (b).

Lubricate the stems of the two intake valves (14) and of the two exhaust valves (11) with engine oil.

Warning

Apply engine oil to the valve stems, however only in the area shown, making sure not to smear the grooves (v).

Install the valves in respective seats in the cylinder head.

Hold

Refitting the valves, closing shims and half rings


Refitting the valves, closing shims and half rings


Hold the closing rocker arm (16) pushed downwards and fit the closing shim (7) on the valve stem up to reach the rocker arm. If using the old cylinder head, start by fitting the original shim.

Refitting the valves, closing shims and half rings


Insert the new half rings (6) in the valve groove (t) and release the rocker arm to obtain shim (7) internal position. Turn the closing rocker arm (16), and compress the spring as much as possible while holding the valve, the shim and the half rings in the valve closed position. Release the rocker arm with a rapid motion, so that the half rings seat in the shim.

Refitting the valves, closing shims and half rings


Refitting the valves, closing shims and half rings


Repeat the procedure with the opposite valve and check that the top of the valve stem is aligned with the surface of the shim (7); if it is not, repeat the half ring installation procedure.

Refitting the valves, closing shims and half rings


Install the closing shims on the intake valves (14) using the method described above for the exhaust valves.

Refit the timing shafts (sect. 9 - 4.4, Refitting the camshafts) to check the valve clearance when closed (sect. 9 - 4.1, Checking and adjusting the valve clearances).

Refitting the opening shims and opening rocker arms

Using an m6 screw, position the opening rocker arm shaft (2) (diameter 9 mm).

Refitting the opening shims and opening rocker arms


Locate the opening rocker arm (3) and drive the shaft home.

Refitting the opening shims and opening rocker arms


Install the four rocker arms (3) in the manner described above.

Refitting the opening shims and opening rocker arms


Raise the opening rocker arm (3) and install the opening shim (5) so it seats against the valve stem.

Refitting the opening shims and opening rocker arms


Release the rocker arm so that it rests against the shim.

Ensure the shim is correctly seated by lightly tapping the rocker arm shoe (a) with plastic mallet.

Refit the timing shafts (sect. 9 - 4.4, Refitting the camshafts) to check the valve clearance when open (sect. 9 - 4.1, Checking and adjusting the valve clearances).

Refitting the opening shims and opening rocker arms


Insert the gaskets (15) on the plugs (12), orienting them (preferably) with the square edge side (t) facing the cylinder head.

Apply prescribed threadlocker on the plug threads (12): apply the product on the first two plug threads, spreading it for the half circumference (about 180).

Tighten the plugs to a torque of 15 nm (min. 14 Nm - max. 16 Nm) (sect. 3 - 3, Engine torque settings).

Note

After tightening, remove any excess of product.

Refitting the opening shims and opening rocker arms


Refitting the opening shims and opening rocker arms


Refitting the opening shims and opening rocker arms


Refitting the opening shims and opening rocker arms


Refitting the opening shims and opening rocker arms


Overhaul of cylinder head components
Cylinder heads Remove any carbon deposits from the combustion chamber and its ducts. Remove any scale from the coolant ducts. Check for cracking and inspect the sealing surfaces for scoring, ri ...

Refitting the cylinder head assemblies
Warning To prevent oil leaks past the contact area between cylinders and crankcase, each time the head is removed, cylinder and piston must be removed as well to clean the mating faces of crankcas ...

Other materials:

Running lights not working
Fault codes Dds: no fault code displayed. Dashboard: no fault code displayed. Location of connections and components (A) low / high beam and parking light connections rear running light and stop light connection. Pin numbering of wiring harness side bbs unit connection. Checks The ...

Refitting the shock absorber support
If you had removed them, apply recommended grease on the threads of the adjusters (4) and the ring nuts (3) having care not to have grease on the surface (c) of the adjusters. Tighten the adjusters on the ring nut side opposite to that featuring flats until bringing the surfaces as close as ...

Front wheel
Nut Washer Left spacer Sealing ring Bearing Front wheel rim Inner spacer Screw Right spacer Front wheel shaft Valve Spare parts catalogue Diavel abs front and rear wheels Diavel carbon abs front and rear wheels Important Bold reference numbers in this section iden ...

2024 | www.dudiavel.com |