Ducati Diavel Service Manual: Specific tools for the engine
88713.2011.Tool to lock crankshaft at top dead centre
88713.2676 .Wrench for tightening cylinder head nuts
88713.2103 Stand for cylinder head assembly
88765.1657 Timing check tool
88713.1821 Wrench for tightening timing belt tensioner pulley shafts
88713.2861 Camshaft oil seal installer
88713.3521 Gearbox output shaft oil seal installer
88713.1806 Holding tool for pulley tightening
97900.0215 Dds (ducati diagnosis system) + cylinder vacuum meter kit
88765.1518 Valve lift gauge
88713.2878 Fork-type feeler gauge 0.2 Mm, 0.3 Mm
88713.3367 Flywheel tool
88713.1920 Tool for installing o-rings on crankcase studs
88713.3334 Plate for gear selector fork positioning
88713.2442 Tool for installation of sealing ring on valve-guide
88713.1749 Puller for drive pulley and cover
88713.1832 Engine repair bench
88713.3408 Wet fcc clutch drum holding tool
88765.1623 Distribution pulley timing tool
88713.1886 Engine cover sheet
88713.1010 Exhaust gases pick-up connector
88713.1805 Tool for tightening timing belt driveshaft pulley
88765.2090 Top dead centre test gauge
88713.3219 Holding tool for pulley tightening
88713.0869 Water pump front seal installer
88713.0870 Installation tool for counter plate for water pump front seal
88700.5749 Crankcase half assembly cap
88713.2877 Spark plug wrench
88713.1980 Punch for installing caps on shafts
88713.3497 Timing belt tensioner pulley wrench
88765.1298 Spacer lower register control valve
88713.2870 Connecting rod guide tool
88713.3394 Punch to install circlip on the camshaft
88713.3406 Wrench for tightening primary sprocket nut
88713.2906Oil filter cartridge wrench
88713.3417 Torque wrench for tightening front sprocket nut
88713.3407 Bush (gear position sensor)
88713.3352Timing tool (clutch plates series)
88713.2069 Rocker arm springs tensioning kit
88713.0944 Oil filter cartridge wrench
88713.2834 Circlip fitting punch
88713.1994 Rocker arm shaft puller
88713.3734 Timing belt tensioner pulley wrench
Spare parts catalogue
Diavel abs workshop service tools
Diavel carbon abs workshop service tools
Service tools
Spare parts catalogue
Diavel abs workshop service tools
Diavel abs workshop service tools
Diavel carbon
abs
workshop service tools
Diavel carbon
abs
workshop service tools ...
Specific tools for the frame
88713.1072 Drift to install half bearing in bottom yoke
88713.2562 Chain assembly tool
88713.1058 Wrench for steering shaft nut
88713.1062 Tool for installing steering head bearings ...
Other materials:
Refitting the front sprocket
Grease the o-ring (16) and install it on the front sprocket spacer (15).
Fit the spacer, from the o-ring side, on the secondary shaft and drive it fully
home against the inner ring of the bearing.
Check that the splines of the gearbox secondary shaft and the sprocket are in
perfect condi ...
Ground connection locations
The negative cable, which is normally connected to the negative pole of the
battery, is fastened to the crankcase. From here, the cable
branches off and splits up within the electrical system to carry the ground
connection to the different elements in the system.
The image shows the ground ...
Checking the engine timing
Set the engine to the configuration described for the "checking and adjusting
the valve clearances", previously indicated.
Install tool 88765.1188 (G) in the spark plug bore to determine the piston tdc,
the gauges (h) on the tool 88765.1518
And the timing check tool (degree wheel (l) 887 ...